- ATTACH
The RH780 and DX20 and TU70 or TU72 must be attached.
- SBIA
DS> ATTACH SBIA HUB SIn
- RH780
DS> ATTACH RH780 SBI RHn (1) (2)
(1) TR level
(2) BR level
8600 :
DS> ATTACH RH780 SIn RHn (1) (2)
(1) TR level
(2) BR level
- DX20
DS> ATTACH DX20 RHn MRA (1)
(1) Device select code for DX20
- TU70
DS> ATTACH TU70 MRA MRAn
- TU72
DS> ATTACH TU72 MRA MRAn
- CCP
The DX20 Console Control Program will prompt with a CCP>
The general command format for the console package is
COMMAND DATA,ADDRESS(CR)
- EXIT
EXIT FROM CCP - Return control to the Diagnostic Supervisor.
Example EXIT(CR)
- LAC
LOAD ACCUMULATOR - Load AC location 7 with data FF.
Example LAC FF,7(CR)
- LCI
LOAD CHANNEL INTERFACE - Load channel interface register 3 with data FF.
Example LCI FF,3(CR)
- LCR
LOAD CRAM - Load CRAM location 40 with data FFFF.
Example LCR FFFF,40(CR)
- LDP
LOAD DATA PATH - Load data path register 3 with data FF.
Example LDP FF,3(CR)
- LDR
LOAD DRIVE REGISTER - Load drive register 3 with FFFF.
Example LDR FFFF,3(CR)
- LIR
LOAD IR - Load IR register with data
Example LIR FFFF(CR)
- LMB
LOAD MASSBUS REGISTER - Load Massbus register 10 from micro processor
Example LMB FF,10(CR)
- LPC
LOAD PC - Load PC with address
Example LPC FFF(CR)
- LUP
LOAD MICROPROCESSOR - Loads an ascii file with an "ADX or CDX" extension
into the CRAM of the DX20'S micro processor starting at location 0.
"CDX" extensions are used when sub files(.ADX) are combined together
to form one file. "ADX" extensions can be used for single files.
Example---LUP FOO,FO1(CR)
Where "FOO" is the subfile(.ADX) within the FO1 file(.CDX)
or
LUP FOO(CR)
- LWM
LOAD WORKING MEMORY - Load working memory location 80 with data FF.
Example LWM FF,80(CR)
- RAC
READ ACCUMULATOR - Read AC data from location 7.
Example RAC 7(CR)
- RCI
READ CHANNEL INTERFACE - Read channel interface register 4.
Example RCI 4(CR)
- RCR
READ CRAM - Read CRAM data from location 40.
Example RCR 40(CR)
- RCA
READ RANGE OF CRAM - Read CRAM data from locations 0 through F.
Example RCA 0,F(CR)
- RDA
READ RANGE OF DRIVE ADDRESSES - Read drive registers from 0 to 1F.
Example RDA 0,1F(CR)
- RDP
READ DATA PATH REGISTER - Read data path interface register 4.
Example RDP 4(CR)
- RDR
READ DRIVE REGISTER - Read drive register 4 from Massbus.
Example RDR 4(CR)
- RE
RESET - Reset DX20.
Example RE(CR)
- RIR
READ IR REGISTER - Read data from IR register
Example RIR(CR)
- RMB
READ MASSBUS REGISTER - Read Massbus register 10 from micro processor.
Example RMB 20(CR)
- RPC
READ PC REGISTER - Read the contents of the PC.
Example RPC(CR)
- RWM
READ WORKING MEMORY - Read working memory location 80.
Example RWM 80(CR)
- RWA
READ A RANGE OF WORKING MEMORY - Read working memory locations 0
through F.
Example RWA 0,F(CR)
- SP
STOP MICROPROCESSOR - Stop DX20 microprocessor.
Example SP(CR)
- ST
START MICROPROCESSOR - Start DX20 microprocessor at location 80.
Example ST 80(CR)
- XCR
EXECUTE MICRO INSTRUCTION - Execute microinstruction at location 1.
Example XCR 1(CR)
- XI
EXECUTE MICROINSTRUCTION IN IR - Execute microinstruction in IR 80 = MOVEI BR.
Example XI 80(CR)
- DEVICE
Type HELP DEVICE device-type for device description.
- EVENT
Event Flag 3 (set) - Invokes the Console Control Program.
- HELP
This program will detect failures in the following areas of the DX20
Programmed Device Adapter:
Massbus Interface
DX20 Microprocessor
Some DX20 Microprocessor Instructions
DX20 Microprocessor Control Store
DX20 Microprocessor Working Memory
In addition a console control package is provided to allow the user
to manually control the DX20 microprocessor and access all DX20
registers. For information on the console control program type
HELP EVMCA CCP.
The following conditions must exist to run this diagnostic:
Memory management must be turned off
The TX03 must be manually switched to the DX20 port under test
- QUICK
The QUICK flag has no effect on this program.
- SECTION
- DEFAULT
Runs all the tests in this diagnostic.
- SELECT
To select the DX20 for testing use the following command.
DS> SELECT ALL
- SUMMARY
This program does not provide a summary report.