- HELP
EVCDA, a FUNCTIONAL level (Level 2R) diagnostic, contains a series
of tests which will establish the functionality of the IEC11-CA.
The program provides error messages which identify data and I/O
errors. The program runs with the Diagnostic Supervisor under the
VAX/VMS operating system.
- DEVICE
Devices supported by this program (EVCDA) are:
IEC11-A
IEC11-B
- IEC11A
Device: IEC11-A IEC BUS CONTROLLER
Link: IEA
Recommended Generic: IEAn
Additional Information:
Unibus CIR: [octal 760010-777770]
Unibus Vector: [octal 2-776]
Unibus BR Level:[decimal 4-7]
IEC11-A Address:[octal 0-35]
- IEC11B
Device: IEC11-B UNIBUS DMA OPTION FOR THE IEC BUS
Link: IBA
Recommended Generic: IBAn
Additional Information:
Unibus CSR: [octal 760010-777770]
Unibus Vector: [octal 2-776]
Unibus BR Level:[decimal 4-7]
IEC11-B Address:[octal 0-36]
- EVENT
Not Applicable.
- QUICK
Not Applicable.
- SUMMARY
None.
- LOAD-DRIVERS
Example command string to load the VMS I/O Drivers
("$" is the System prompt, "SYSGEN>" is the SYSGEN program prompt)
$ MCR SYSGEN
SYSGEN> LOAD DEV:[directory]IEDRIVER
SYSGEN> LOAD DEV:[directory]IBDRIVER
SYSGEN> CONNECT IEA/ADAPTER=*/VECTOR=%O[vector]/CSR=%O[CIR address]
SYSGEN> CONNECT IBA/ADAPTER=*/VECTOR=%O[vector]/CSR=%O[CSR address]
SYSGEN> EXIT
- ATTACH
Example command strings to LOAD, ATTACH and SELECT the IEC11-CA
LOAD EVCDA.EXE
ATTACH appropriate Unibus Adapter to main processor bus
ATTACH IEC11A DW0 IEA 760010 270 6 35
ATTACH IEC11B DW0 IBA 760020 274 6 36
SELECT ALL
- REQUIREMENTS
HARDWARE:
IEC11-CA (An IEC11-A and an IEC11-B)
BC08S-1 BUS ADAPTER CABLE (connected IEC11-A to IEC11B)
SOFTWARE:
VMS ENVIRONMENT:
VAX Diagnostic Supervisor (minimum, Version 6.3)
VAX/VMS Operating System (minimum, Version 2)
VMS I/O Drivers, IEDRIVER.EXE and IBDRIVER.EXE
Privilege to run SYSGEN
- SECTIONS
The following sections are contained in this program (EVCDA):
LOGIC TEST SECTION
ALOGIC TEST SECTION
BLOGIC TEST SECTION
CLOGIC TEST SECTION
DATA TEST SECTION
- LOGIC
LOGIC TEST SECTION
The LOGIC test section will run all of the following test sections,
in the order given. This section does not in itself contain any tests.
It is merely a convenience for the user to run all of the logic test
sections via one command.
ALOGIC TEST SECTION
BLOGIC TEST SECTION
CLOGIC TEST SECTION
- ALOGIC
ALOGIC TEST SECTION
The ALOGIC test section contains the tests which will verify the
functionality of, and interaction between, the IEC11-A control
registers. Only the IEC11-A is accessed.
- BLOGIC
BLOGIC TEST SECTION
The BLOGIC test section contains the tests which will verify the
functionality of, and interaction between, the IEC11-B control
registers. Only the IEC11-B is accessed.
- CLOGIC
CLOGIC TEST SECTION
The CLOGIC test section contains the tests which will verify the
functionality of, and interaction between, the IEC11-A and the IEC11-B.
Both the IEC11-A and the IEC11-B are accessed.
- DATA
DATA TEST SECTION
The DATA test section contains the tests which will perform an overall
verification of the IEC11-CA. Both the IEC11-A and the IEC11-B are
accessed.